Essential Towable Inspection

Essential Inspection Points for Towable RVs (Travel Trailers and 5th Wheels)

 

 

This report will consist of 25 to 30 photos describing the items that have been identified during the detailed Essential Towable Inspection.

 

Roof

  • Inspect and rate the overall Roof
  • Rate the condition of the roof vents, air conditioners, antenna and other components that are mounted on the roof.

 

Sidewall and End Caps

  • Inspect and evaluate the appearance and functional condition of the sidewalls, entrance doors, windows, and cargo access

 

Slide Out Rooms

  • Inspect and rate the roof
  • Inspect and evaluate the condition of the seals, sweeps and gaskets for possible

 

Awnings and Slide Out Toppers

  • Operate and rate condition of the awning frames and latching

 

Chassis Turn Signal and Running Lights (12-volt DC)

  • Operate and evaluate the emergency break away
  • Activate and evaluate the operation of the DOT lights mounted on the

 

120 Volt AC Electrical System (house type power)

  • Inspect and rate the condition of the power cord and its connection
  • Remove cover panel of 120-volt circuit breaker box to visually inspect the condition of the wiring, circuit breakers and grounding
  • Test and verify the output operation of the 120 VAC to 12 VDC converter for charging of the deep cycle

 

Generator if installed *strongly recommend performing oil analysis to determine internal combustion engine component condition.

  • Identify and note the model, serial number and run hours of the generator.
  • Check oil level.
  • Start and operate the onboard

 

Inverter if installed

  • Identify and note the model and serial number of the
  • Visually inspect the wiring and electrical connections and fuses/circuit

 

Coach Battery System – (12-volt DC deep cycle Battery Electrical System)

  • Evaluate the condition, age, and matched sizing of the battery
  • Access and visually inspect the wiring, fuse panel and fuses of the 12-volt DC electrical

 

Fresh Water System

  • Verify the fresh water connections for the City Water hookup are
  • Verify the onboard fresh water tank and pressure pump system will operate and maintain

 

Waste Water Systems – (Gray and Black Water)

  • Operationally test and inspect both waste (gray and black) plumbing systems for leaks under the sinks, shower, around the toilet and discharge lines.
  • Operate both drain valves and test for ease of
  • Verify the drain cap is in place and will hold waste

 

Life Safety Items

  • Perform and document LP gas timed leak test at cook top burner spud for 5 minutes at 8 inches of water column gas
  • Test the Ground Fault Circuit Interrupter (GFCI) circuits in the 6-foot range of the water areas of the bathroom, kitchen and exterior receptacles.
  • Test all wall receptacles for correct polarity and ground
  • Test the exterior skin for Hot Skin that would cause electrical
  • Emergency Exit Windows – Verify all safety windows are
  • Fire Extinguisher – Verify unit is secure in bracket and dial indicates extinguisher is fully
  • Smoke/Fire Detector –Test and verify operation of
  • Carbon Monoxide Detector (if applicable) – Test and verify operation of
  • LP Gas Detector – Verify gas detection and audio Document expiration date of detector.
  • Verify the rubber grommet is properly sealed around LP gas line of water

 

LP Gas System

  • Visually inspect all hoses and pressure regulators for damage and age
  • Verify plastic cover has been installed over

 

DOT Cylinders – if equipped

  • Document the manufacturer dates of DOT
  • List the tank sizes that have been
  • Conduct visual inspection of exterior of cylinder for rust and other

 

ASME tank if equipped

  • If tank is visible, conduct a visual inspection of tank for rust or physical

 

Refrigerator

  • Identify the brand, model, and type of
  • Operate on all heat sources – 120-volt AC, LP gas and for 3-way refrigerators, 12-volt
  • Collect serial and model number and verify with manufacturer if recall notice has been issued and completed for this unit.

 

Water Heater

  • Identify the brand, model, and type of water

 

  • Fill tank with water (if necessary) and verify operation on all heat sources – LP gas and 120-volt AC if equipped with heating

 

Furnace

  • Operate and verify warm air discharge out of vents and proper return air flow to

 

Cook Top/ Stove

  • Verify the ignition and operation of all top burners and the oven flame (if equipped).

 

Air Conditioner(s)

  • Perform cooling efficiency test (Delta T) on each

 

Washer/ Dryer

  • Visually inspect and verify a wash and rinse cycle of the washer and
  • Evaluate and rate the exterior condition of the dryer exhaust

 

Microwave/Convection Oven

  • Identify and list the brand, model, type, and output wattage of the

 

Dishwasher if installed

  • Identify and list the brand, model, and type of unit.

 

In House Vacuum System – if installed

  • Identify and list the brand, model, and type of unit.

 

Electric Fireplace if installed

  • Identify and list the brand, model, and type of unit.

 

Cook Top Exhaust Fan

  • Operate and verify condition of the exhaust function and fan

 

Ceiling Mounted Fans and Ceiling Exhaust Vents

  • Operate and verify condition of the blade direction and fan

 

Interior Conditions and Appearance

  • Visually inspect all ceilings, walls, interior doors and flooring for signs of water intrusion, surface damage and/or
  • Operate all interior, exterior and décor lighting – 12-volt and 120-volt.

 

Cabinets and Closet Condition

  • Inspect and evaluate all cabinet doors, drawers, and pull-out

 

Furniture

  • Visually inspect the condition of the dinette table/booth, chairs, recliners, and
  • Visually inspect and note signs of mattress damage or

 

Entertainment System

  • Visually inspect and operate all TV and stereo
  • Verify DVD/disc players and radios are

 

Shower/Tub Enclosure

  • Evaluate and rate the seals around the frame work and doors for water
  • Operate the door and latch system to verify its

 

Running Gear (Towable)

  • Type and number of axles.
  • Inspect the frame, axles, springs, rims and other components for rust, oil stains and visible
  • Document the information on the tires as to their age and weight

 

Hitch System/Hook Up

  • Inspect and identify the type of system used to tow

 

Leveling System

  • Operate by extending and retracting

 

Weight Labels and Data Plates

  • Identify and document the Vehicle Identification Number (VIN).
  • Document the License plate
  • List the Inspection sticker information – if
  • List the RVIA inspection seal
  • List the Gross Vehicle Weight
  • List date of